Ống chống mài mòn: Khi nào bạn cần lót gốm?

Trả lời nhanh:

You need ceramic lining when a steel pipe wears out within two years. It is also needed when rubber cannot handle the load. Ceramic lining is recommended at high-velocity bends, elbows, reducers, tees, and other flow-direction changes where wear concentrates. YOUFUMI builds abrasion-resistant pipe and fittings from steel shells with bonded ceramic faces for slurry and dry solids. The company runs its own pipe factory, valve factory, and clean workshop, so lining work stays in-house.

What is An Abrasion-Resistant Ceramic-Lined Pipe?

MỘT abrasion-resistant ceramic-lined pipe is a steel pipe with a hard ceramic layer bonded to its inner wall. The steel carries the pressure and handles installation loads. The ceramic faces the flow and absorbs the wear.

On the Mohs scale, alumina rates about 9, which is harder than steel or rubber. For example, a 20-mm steel wall is worn down to 1mm in 8 months. A lined pipe in similar duty kept 3mm to 4mm of wall after 12 months.

Ceramic is also resistant to acids and alkalis and remains strong even at high temperatures. Its smooth face resists buildup of ash, coal dust, and slurry. The abrasion resistant ceramic lined pipe is also lighter than solid wear alloy pipe of the same bore. It expands about half as much as steel when heated, so you must design the bond carefully for high temperatures.

How Do You Choose Between Alumina and Zirconia Ceramic Lining?

Choose alumina for abrasion-dominated lines and zirconia for impact-dominated ones. Alumina is harder and costs less, so it is ideal for sand, ash, and fine slurry. Zirconia is tougher, so it survives coarse particles striking at steep angles.

Alumina-zirconia blends, often called ZTA, sit between the two. Zirconia typically costs two to four times more per part. You should only use it where chipping, not sliding wear, ends the liner’s life.

Moreover, ceramic is brittle. Sudden impact and a big temperature swing can crack it. For lines carrying large rock, consider rubber or hardened steel instead.

What Should You Know About Pipe, Elbows, Tees and Reducers?

For ceramic-lined abrasive service, straight pipe, elbows, tees, and reducers must be engineered as one continuous flow path. Elbows usually wear out first, so line them first. Flow hits the outer curve at high impact angles and removes material fast. Line the curve and the first straight section after it, because the stream stays turbulent there.

Tees, crosses, and laterals take the same stress at branch points. Reducers speed up the flow and raise local wear. Each fitting gets ceramic tiles or a cast ceramic face matched to its wear pattern.

Bộ giảm đồng tâm có lót

Các Phương pháp Lót Khác nhau; Mật độ Cao; Khả năng chống thẩm thấu Cao; Khả năng Chân không

Xem chi tiết sản phẩm

A straight wear resistant pipe wears more slowly. Many projects line only the fittings and a short run after each one. This reduces cost where wear is low. Use flanged ends so crews can swap a worn spool without cutting steel. You should also mark each spool with its flow direction, because lined elbows have a defined wear face. Also match flange drilling to ASME B16.5 or EN 1092-1.

What Are the Applications of Ceramic Lining in Mining, Power, Cement, Dredging and Ash?

Ceramic lining suits any abrasion resistant pipe duty where hard particles move at speed. Typical duties include:

• Mining: tailings, concentrate slurry, and gold circuit lines.
• Power: pulverized coal, fly ash, and bottom ash conveying.
• Cement: raw meal, kiln dust, and fuel transport.
• Dredging: sand and gravel slurry in discharge lines.
• Ash handling: hydraulic and pneumatic ash and slag removal.

This table summarizes the applications where ceramic lined pipes are used:

How Do You Specify a Wear-Resistant Lined Pipe?

Specify a wear-resistant lined pipe by giving the supplier your full duty data. A good request lists:

• Particle size, hardness, and concentration by weight.
• Flow rate, velocity, and impact angle at bends.
• Fluid pH and temperature range.
• Design pressure and flange standard.
• Target service life and shutdown interval.

You should also request hardness records and bond test results for each batch. Request a drawing that shows the lined inner diameter, because the liner reduces the bore. Also plan to replace linings before wear becomes visible, since a breakthrough means a spill. You should also agree on the inspection method, such as thickness gauging at elbows, before the pipe ships.

Rổ lọc có lót

Erosion resistance; Different Meshes Available; Darin Valve Available; Easy Operation

Xem chi tiết sản phẩm

Phần kết luận

Choose an abrasion resistant pipe with ceramic lining when abrasion, not impact, ends your pipe’s life. Match alumina or zirconia to the particle load, and line elbows and fittings first. Rubber or hardened steel is the better choice for heavy rock.

For abrasive slurry lines, consider YOUFUMI ceramic lined steel pipe. For valves in the same service, consider the YOUFUMI ceramic valve range, and share your slurry data for a liner recommendation.

Những câu hỏi thường gặp

What is the most wear-resistant pipe?

The most wear-resistant pipe for abrasive slurry is a ceramic lined steel pipe. Alumina and zirconia faces outlast steel, stainless steel, and rubber in fine-particle service.

When should I choose ceramic lining over rubber or hardened steel?

Choose ceramic for fast, fine, hard particles, high temperatures, or chemical attack. Choose rubber for large rocks and heavy impact. Choose hardened steel where impact is high and abrasion is moderate.

How do I work out whether I need ceramic lining?

To decide whether you need ceramic lining, check how fast your current pipe wears. If it fails within about two years, or you replace elbows every few months, lining likely pays back. Compare cost per year of life, not purchase price.

Does ceramic lining reduce flow or increase pressure drop?

The liner reduces the inner diameter slightly, which raises velocity. Its smooth face lowers friction and resists buildup. Size the pipe on the lined bore and check pressure drop with your supplier.